sphenix-hcal-l AT lists.bnl.gov

Subject: sPHENIX HCal discussion

List archive

Re: [Sphenix-hcal-l] [Sphenix-emcal-l] T-1044 continues

From: "Huang, Jin" <jhuang AT bnl.gov>
To: "Haggerty, John" <haggerty AT bnl.gov>, "sphenix-hcal-l AT lists.bnl.gov" <sphenix-hcal-l AT lists.bnl.gov>, "sphenix-emcal-l AT lists.bnl.gov" <sphenix-emcal-l AT lists.bnl.gov>
Subject: Re: [Sphenix-hcal-l] [Sphenix-emcal-l] T-1044 continues
Date: Fri, 18 May 2018 11:00:07 +0000

Hi, John and all

Thanks for taking care of this epic beam test.

The automatic data production is running:
https://wiki.bnl.gov/sPHENIX/index.php/2018_calorimeter_beam_test/Data_Production_and_Analysis#Production_Information
We have tower-by-tower and energy scale calibration for EMCal. However,
there is no tower-by-tower calibration on HCal yet. I would invite double
check the HCal energy scale too, which was initially set by Xu Sun in the 1st
iteration of the test.

Cheers

Jin

______________________________

Jin HUANG

Associate Physicist
Brookhaven National Laboratory
Physics Department, Bldg 510 C
Upton, NY 11973-5000

Office: 631-344-5898
Cell: 757-604-9946
______________________________

> -----Original Message-----
> From: sPHENIX-EMCal-l [mailto:sphenix-emcal-l-bounces AT lists.bnl.gov] On
> Behalf Of John Haggerty
> Sent: Thursday, May 17, 2018 8:47 PM
> To: sphenix-hcal-l AT lists.bnl.gov; sphenix-emcal-l AT lists.bnl.gov
> Subject: [Sphenix-emcal-l] T-1044 continues
>
> The (hopefully) final chapter of T1044-2018, 2018c, has begun. We are
> running between the cracks of T992, and to get the aluminum HCAL installed,
> I needed help with rigging from Todd and Jim. The MI beam has been a little
> spotty this week, so T992 is a bit panicky
>
> Long story short, I got here a little early while the beam was off, and it
> appeared like my best bet was to put the aluminum in immediately.
> It's now done:
>
> > https://photos.app.goo.gl/aonmy19NENH72jLy1
>
> and our team (Jonathan, Milap, and Debbie) is ready to go.
>
> I have had a look at some 120 GeV protons and it looks like I have the
> hodoscope in the right place again and it looks like it's centered on Tower
> 36
> in the emcal. I'm having some problems with the Cerenkov counters that I'm
> trying to sort out.
>
> If all goes well, it looks like we'll get access to the beam tomorrow
> afternoon
> or evening, but we're working out with our colleagues exactly when we'll
> run.
>
> --
> John Haggerty
> email: haggerty AT bnl.gov
> cell: 631 741 3358
> _______________________________________________
> sPHENIX-EMCal-l mailing list
> sPHENIX-EMCal-l AT lists.bnl.gov
> https://lists.bnl.gov/mailman/listinfo/sphenix-emcal-l

[Sphenix-hcal-l] T-1044 continues, John Haggerty, 05/17/2018
- Re: [Sphenix-hcal-l] [Sphenix-emcal-l] T-1044 continues, Huang, Jin, 05/18/2018