sPHENIX discussion of the superconducting solenoid

["Yip, Kin" <kinyip AT bnl.gov>]

Dear Mike,

Can you answer Ed's question ?

Ray Ceruti's email seems to imply that we can just leave the tie rod in the tight position in the yellow frame for storage in 912  (and even if we purge the system with dry Nitrogen), rather than loosening it (after taking the magnet out and putting it inside the yellow frame in 912) and then in late 2021 tightening it again (just before the transportation to 1008) ?

But to make sure, can you please advise ?

Kin

-------- Original message --------

From: "O'Brien, Edward" <eobrien AT bnl.gov>

Date: 11/8/19 13:34 (GMT-05:00)

To: sphenix-magnet-l AT lists.bnl.gov, "Yip, Kin" <kinyip AT bnl.gov>bject: Re: [Sphenix-magnet-l] What to do while in storage in 912

    Dear all,
     Do we want to store the SC-Magnet long term
    in the transport frame with the tie rods tight, or loose?
    Does it matter? Thanks.

    Ed

On 11/4/2019 6:30 PM, Yip, Kin wrote:

Hi,

 

The series of emails below provides the information for what to do while the Magnet/Cryostat is in the yellow frame at 912.    We’ll purge the system with dry nitrogen.

 

Kin

 

From: Than, Yatming (Roberto) <ythan AT bnl.gov>
Sent: Tuesday, November 5, 2019 4:59 AM
To: Yip, Kin <kinyip AT bnl.gov>; Ceruti, Raymond B <rayc AT bnl.gov>; Phillips, David B <phillips AT bnl.gov>; Mills, James A <mills AT bnl.gov>; Anerella, Michael D <mda AT bnl.gov>; Streckenbach, Brian <bstreckenbach AT bnl.gov>; Orfin, Paul <porfin AT bnl.gov>
Subject: RE: Restraints are installed

 

We do not need to have a tight seal, with regards to pressure.

We will try to tape bags around the restraints ends to keep a moisture barrier around them.

Then refresh the dry nitrogen once in a while.

Bottom line is to keep moisture away from the internal electrical connectors.

R.

 

From: Yip, Kin <kinyip AT bnl.gov>
Sent: Monday, November 04, 2019 3:45 PM
To: Ceruti, Raymond B <rayc AT bnl.gov>; Phillips, David B <phillips AT bnl.gov>; Mills, James A <mills AT bnl.gov>; Anerella, Michael D <mda AT bnl.gov>; Streckenbach, Brian <bstreckenbach AT bnl.gov>; Than, Yatming (Roberto) <ythan AT bnl.gov>
Subject: RE: Restraints are installed

 

Hello,

 

In addition to the detailed replies below and Ray also replied to me privately :    

 

“The L2 will certainly leak to some small degree but certainly won’t hold pressure or vacuum.  If all are OK with this it would be no problem.”

 

I think Ray meant N2 (dry nitrogen), not L2.  

 

If everybody is OK with N2 leaking a bit, we don’t need to replace the heat shield restraints ?!  

 

Roberto, do you think we can at least try this (without removing heat shield restraints) and see how bad the leak is and how long before we’ll need to do the purging again ?

That’s what you implied the last few times that we discussed about this ??   Or you think we should remove heat shield restraints to have the original discs for better seal ?

( Obviously, the latter implies more work as we’ll need to put back the heat shield restraints again in late 2021 before transportation. )

 

Kin

 

From: Ceruti, Raymond B <rayc AT bnl.gov>
Sent: Tuesday, November 5, 2019 4:28 AM
To: Phillips, David B <phillips AT bnl.gov>; Yip, Kin <kinyip AT bnl.gov>; Mills, James A <mills AT bnl.gov>; Anerella, Michael D <mda AT bnl.gov>; Streckenbach, Brian <bstreckenbach AT bnl.gov>; Than, Yatming (Roberto) <ythan AT bnl.gov>
Subject: RE: Restraints are installed

 

Hi All,

 

           2) the doors will have to be installed, the heat shield restraints would have to be removed to replace the original discs that have O ring seals in order to hold any L2 pressure.

           3) I don’t see any reason that the tightened cold mass rods will effect purging if N2.  (As long as you don’t cool down)

           4) Heat shield supports won’t hold any pressure as stated before.

           5) Valve box extension supports should be in place before the doors are installed to support the extra weight.  No effect otherwise.

 

From: Phillips, David B <phillips AT bnl.gov>
Sent: Monday, November 04, 2019 2:36 PM
To: Ceruti, Raymond B <rayc AT bnl.gov>; Yip, Kin <kinyip AT bnl.gov>; Mills, James A <mills AT bnl.gov>; Anerella, Michael D <mda AT bnl.gov>; Streckenbach, Brian <bstreckenbach AT bnl.gov>; Than, Yatming (Roberto) <ythan AT bnl.gov>
Subject: RE: Restraints are installed

 

Kin/Mike/Jim,

 

After we move the cryostat to the yellow shipping frame then it will be spending some time on the floor of B912 before it’s shipped to 1008.

While it’s in storage do we:

1. Purge with N2?
2. Pump with rough vacuum (would require putting doors on the new doghouse)?
3. What should be the state of the cold mass supports?
4. What should be the state of the heat shield supports?
5. Does the installation of the Valvebox extension supports affect any of the above?

 

Dave

 

From: Ceruti, Raymond B <rayc AT bnl.gov>
Sent: Monday, November 04, 2019 2:10 PM
To: Yip, Kin <kinyip AT bnl.gov>; Phillips, David B <phillips AT bnl.gov>
Subject: Restraints are installed

 

Hi Kin and Dave,

 

     The XPhenix rods are tight and the heat shield restraints are installed.  Once you have move the solenoid out of the iron I can install the support struts for the valve box extension.

 

Regards,

Ray 

_______________________________________________
sPHENIX-magnet-l mailing list
sPHENIX-magnet-l AT lists.bnl.gov
https://lists.bnl.gov/mailman/listinfo/sphenix-magnet-l